Yellow Bullet Forums banner
1 - 20 of 35 Posts

· Registered
Joined
·
1,718 Posts
I run a NAPA commercal battier, have had it on my winch for about 4 years now and still going strong. Befor that I used a Del-co deep cycle battier and it lasted 5 1/2 years.
 

· RED ROCKET
Joined
·
8,637 Posts
i use a optima blue top...i have a trickle charger in the cabinet as well so as long as the generator is running or the the trailer is plugged in the battery charges..worked great all year.
 

· Registered
Joined
·
26,611 Posts
760CCA Group 31. I would use either a Trojan or East Penn/Deka. No need for a dry cell.
 

· Registered
Joined
·
26,611 Posts
I would use a regular wet cell. The AGM is like 3x the cost. Deep cycles are almost 2x as much. If you are just winching, it will be like a start application for the battery. It is designed mainly to drop tons of amperage when starting a big truck. If you were using a smaller automotive sized battery you would be cycling it much deeper than the group 31. If you are going to use it for other things (stereo, lights, etc) while not a charger, then consider a deep cycle.
 

· Peeing In Your Cheerios
Joined
·
8,512 Posts
Discussion Starter · #10 ·
I would use a regular wet cell. The AGM is like 3x the cost. Deep cycles are almost 2x as much. If you are just winching, it will be like a start application for the battery. It is designed mainly to drop tons of amperage when starting a big truck. If you were using a smaller automotive sized battery you would be cycling it much deeper than the group 31. If you are going to use it for other things (stereo, lights, etc) while not a charger, then consider a deep cycle.

I found this
http://www.batteryprice.com/deka-9a31-agm-automotive-group31-battery.aspx

The others look like soooo much money.
Can I use a regular car battery?
 

· Registered
Joined
·
26,611 Posts
I think one of the pins on some trailer plugs is for doing that. We have had others run cables with Anderson Ends for charging the battery through out the day. They were work trucks.
 

· Registered
Joined
·
26,611 Posts
I found this
http://www.batteryprice.com/deka-9a31-agm-automotive-group31-battery.aspx

The others look like soooo much money.
Can I use a regular car battery?
You can use one. But look up a East Penn Deka 1031 MF battery. Should be available for well under $100 at any big truck stop, repair center, or a battery supplier. Make sure to only get the 760CCA battery (it actual will test around 1000amps). The 760 will last longer than the higher CCA batteries. The 1031 is less money, and will last 2 years longer on average. (Because the plates are thicker)
 

· Peeing In Your Cheerios
Joined
·
8,512 Posts
Discussion Starter · #13 ·
You can use one. But look up a East Penn Deka 1031 MF battery. Should be available for well under $100 at any big truck stop, repair center, or a battery supplier. Make sure to only get the 760CCA battery (it actual will test around 1000amps). The 760 will last longer than the higher CCA batteries. The 1031 is less money, and will last 2 years longer on average. (Because the plates are thicker)
Dude, I just learned that they have an office within a mile of my house.
Ill go tomorrow.

Thanks!
 

· Registered
Joined
·
26,611 Posts
Dude, I just learned that they have an office within a mile of my house.
Ill go tomorrow.

Thanks!
LOL, you are welcome. They are the biggest manufacturer on American soil that I know of.
 

· Registered
Joined
·
26,611 Posts
4ga is a bit overkill, likely 6g will work fine. The battery if really down will accept 50ish amps for a couple of minutes and then drop off fairly quickly to 25amps. So really heavy cables are not necessary. But bigger is better, so dont let me discourage you from the 4ga. :) You can get Anderson Ends in 4 and 6ga as well as really heavy guages. If you go with 4ga, and use Anderson Ends, you can use the hookup for other things too, like a booster cable, 12volt outlet, etc.
 
1 - 20 of 35 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top