Yellow Bullet Forums banner

Dyno Videos and Results

539K views 1K replies 286 participants last post by  Ed Curtis 
#1 ·
I always take vids at the dyno and never end up putting them on the computer because it's too much work LOL.

Post em up!!!
 
#67 ·
#71 ·
Re: PLEASE POST YOUR DYNO VIDS

My Uratchko 440" Yates N/A build. Made peak power of 1021 HP at 8800 RPM. This pull is from 7000-9000 RPM. Dyno header tubes were too small, and too long for our build.

 
#73 · (Edited)
Re: Dyno Videos

http://www.youtube.com/watch?v=8tLiyh9_p8Y

Try this of my BBC in the spring. It was only the 3rd pull on it and was still too lean. Dyno had no fresh air for carb and I had headers open in cell. Motor made an extremely flat curve of 1,010 hp @6000-6500 and 890 lbs of tq @5200-5600. Computer dyno software now says it's pushing 1,150 hp for ET and weight.
 
#75 ·
#77 ·
Re: Dyno Videos

Figured I'd post up an FE for you guys to watch. Thsi was on Jimkidd's dyno a couple weeks ago.

http://www.youtube.com/watch?v=QR1E92NUsTU

This is a 482 cube 427 based FE Ford engine with individual runner EFI. It has a hydraulic roller cam and 103.5:1 compression, running on 93 octane pump gas from the local Exxon.
These were a few tuning pulls - so you'll see and hear some partial hits and an occassional poof out of hte stacks. It ended up making 603 horsepower and 624 torque.
Look out for sparks - the pulleys are just used junk for testing - it'll get fancy billet stuff in the car, and they touched at high RPM.
 
#80 · (Edited)
Re: Dyno Videos

:D very happy with the way my engine turned out

http://www.youtube.com/watch?v=cIkLctL1S0A

New Dart Little M block
New Callies Compstar 4.000 foged steel crankshaft
New Callies Compstar 6" forged I beam steel connecting rods with ARP 2000 Bolts
New JE forged pistons 13.5:1+
New Total Seal Gapless rings
New Clevite 77 Tri-Armor coated performance rod and main bearings
New Durabond cam bearings
New Melling race high volume oil pump
New Victor Reinz performance gasket's
New MLS Head gaskets
New Tru roller billet timing chain with torington bearing, lock plate and cam button
New CNC custom ground solid roller camshaft
New Crower heavy duty lifters
New Comp Cams Hi-Tek pushrods
New Crower shaft rocker arms
New 235 Air flow research aluminum cylinder heads (spread port exhaust) Titanium retainers,
New CNC Custom valve covers
New Kevko 7qt quart drag race oil pan
New Dart Dominator ported intake manifold
New TCI / ATI SFI race balancer
Professional assembled and machined inhouse by CNC-Motorsports, we spare no cost for quality.
Price includes engine break in on our in house DTS engine dyno

http://www.youtube.com/user/looker195772camaro?feature=mhum#p/u/0/DjI0I9gA1Jo
 
#91 ·
Re: Dyno Videos

LOL...a younger Maskin, in 1990 in his brand new dyno room at Dart.
I sat and talked with him for an hour or so last thursday at Indy....he said he has over 20,000 pulls himself on that dyno.
 
Top