cam recommendation - Yellow Bullet Forums

Go Back   Yellow Bullet Forums > Technical Section > Valvetrain - LGM Racing and Development

Valvetrain - LGM Racing and Development

Reply
 
Thread Tools Display Modes
Old 03-07-2012, 03:16 PM   #1
junk racing
Junior Member
Spooled up
 
Join Date: Nov 2010
Location: wylie texas
Posts: 135
Default cam recommendation

I am changing my heads and think a camshaft upgrade is in order aswell. I do drive this car on the street and its a pumpgas motor specs as follows. I am changing to AFR 210's and a solid roller


355
010 block
billet main caps
eagle crank
eagle h beams
srp flat tops 11.1 compression
sportsman 2's changing to afr 210's
cam currently is a lunati solid flat #40119 256/268 .550 .571@.50 Want solid roller
victor jr intake ported
NX dual stage plate pilled at 200
proform 750

Built turbo 350 without brake
TCI 4000 stall

Strange 9'' with 3.89 gear

car weighs 3200 but will be lightning it up a bit.

Thanks in advance
junk racing is offline   Reply With Quote
Sponsored Links
Advertisement
 
Old 03-07-2012, 03:33 PM   #2
CamKing
Senior Member
Smoked another BBC
 
CamKing's Avatar
 
Join Date: Jan 2009
Posts: 1,785
Default Re: cam recommendation

What RPM do you want to turn it?
What rocker ratio do you have?
Are the AFR heads "As Cast" or CNC ported?
__________________
Mike Jones
Jones Cam Designs
Denver, NC 28037 704-489-2449
http://jonescams.com
jonescams@bellsouth.net

Last edited by CamKing; 03-07-2012 at 03:35 PM.
CamKing is offline   Reply With Quote
Old 03-07-2012, 08:04 PM   #3
junk racing
Junior Member
Spooled up
 
Join Date: Nov 2010
Location: wylie texas
Posts: 135
Default Re: cam recommendation

1.5 rockers
No more than 7200 RPM if i can help it
The heads have the race porting not the competition port job.
junk racing is offline   Reply With Quote
Old 03-08-2012, 11:27 AM   #4
CamKing
Senior Member
Smoked another BBC
 
CamKing's Avatar
 
Join Date: Jan 2009
Posts: 1,785
Default Re: cam recommendation

Part# R76424-78410-110
254/262 @.050"
.424"/.410" Lobe Lift
110 LSA
__________________
Mike Jones
Jones Cam Designs
Denver, NC 28037 704-489-2449
http://jonescams.com
jonescams@bellsouth.net
CamKing is offline   Reply With Quote
Old 03-08-2012, 12:47 PM   #5
mikes
Member
Pullin gears
 
mikes's Avatar
 
Join Date: Sep 2006
Location: High Tax State.
Posts: 782
Default Re: cam recommendation

Cam King, If you dont mind me asking, (and to the OP sorry to butt in on your thread), why do you spec a 110 over the 106 LSA for a 350? I have a slightly smaller hydraulic roller that I was going to run solid lifters on in a similiar combo but was told its no good as its on a 110 vs a 106 and would be a slouch. I will pm you my combo for your thoughts regarding my application.
mikes is offline   Reply With Quote
Old 03-08-2012, 01:14 PM   #6
CamKing
Senior Member
Smoked another BBC
 
CamKing's Avatar
 
Join Date: Jan 2009
Posts: 1,785
Default Re: cam recommendation

Quote:
Originally Posted by mikes View Post
Cam King, If you dont mind me asking, (and to the OP sorry to butt in on your thread), why do you spec a 110 over the 106 LSA for a 350?
Because of this
"NX dual stage plate pilled at 200" and this "11.1 compression"

Without the Nitrous, I'd recommend less exhaust duration, and a 108 LSA.
__________________
Mike Jones
Jones Cam Designs
Denver, NC 28037 704-489-2449
http://jonescams.com
jonescams@bellsouth.net
CamKing is offline   Reply With Quote
Old 03-08-2012, 01:26 PM   #7
mikes
Member
Pullin gears
 
mikes's Avatar
 
Join Date: Sep 2006
Location: High Tax State.
Posts: 782
Default Re: cam recommendation

Oh ok, it helps if I read the ENTIRE post
mikes is offline   Reply With Quote
Old 03-09-2012, 08:58 AM   #8
mdracer
Junior Member
Spooled up
 
Join Date: Oct 2008
Location: So. central Pa.
Posts: 231
Default Re: cam recommendation

mdracer is offline   Reply With Quote
Old 03-29-2012, 09:45 PM   #9
yankees
Junior Member
Spooled up
 
Join Date: May 2009
Posts: 105
Default Re: cam recommendation

camking what r u going to do with the Sportsman II's?
yankees is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -4. The time now is 01:50 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Garage Plus vBulletin Plugins by Drive Thru Online, Inc.
Resources saved on this page: MySQL 3.03%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Yellow Bullet LLC