PDA

View Full Version : 9" for fox body

RADRACER
10-29-2008, 02:34 PM
need a 9"housing and axles for a fox body. any suggestions.
bad466
10-29-2008, 03:54 PM
There was one for sale in the classifieds about a week or two ago.
OB1
10-29-2008, 04:09 PM
need a 9"housing and axles for a fox body. any suggestions.
Get a Chris Alston Fab 9 with undermount anti-roll 1.25 60' on 275 radial
Scott @ DLS
10-29-2008, 04:26 PM
need a 9"housing and axles for a fox body. any suggestions.


What power level do you plan on running?
dougd
10-29-2008, 05:20 PM
The Moser 9 inch housing and axle package is a good alternative a well.
Pwraddr
10-29-2008, 08:52 PM
Get a Chris Alston Fab 9 with undermount anti-roll 1.25 60' on 275 radial


Geometry problems I believe.....
quarterstang86
10-31-2008, 11:26 PM
I would go straight to Dave @ TeamZ without hesitation of looking right past anything Alstons or M9.
mideastbusa
10-31-2008, 11:31 PM
Geometry problems I believe.....

If you lower it,which almost everyone does.
Pwraddr
11-01-2008, 10:56 AM
I would go straight to Dave @ TeamZ without hesitation of looking right past anything Alstons or M9.


+1 I agree. He is the one that told me of the geometry issues on some of the fabbed stuff.

www.teamzmotorsports.net (http://www.teamzmotorsports.net)
67AfroMaro
11-01-2008, 12:31 PM
+1 I agree. He is the one that told me of the geometry issues on some of the fabbed stuff.

www.teamzmotorsports.net (http://www.teamzmotorsports.net)


Geometry? Do tell...

I know a lot of people running CA-Chassisworks stuff without issue.
slowstang
11-01-2008, 12:48 PM
alot of aftermarket housings have the centerline of the bushing or sperical ends, to high compared to factory. so when installed the control arms are moved up toward the bottom of the floor. look at mosers web site the look at stranges web site ,you will see strange notches the housing to drop the mount down in the housing
67AfroMaro
11-01-2008, 12:51 PM
alot of aftermarket housings have the centerline of the bushing or sperical ends, to high compared to factory. so when installed the control arms are moved up toward the bottom of the floor. look at mosers web site the look at stranges web site ,you will see strange notches the housing to drop the mount down in the housing

Ah... loss of leverage. IC. Chassisworks does this?
mideastbusa
11-01-2008, 01:03 PM
alot of aftermarket housings have the centerline of the bushing or sperical ends, to high compared to factory. so when installed the control arms are moved up toward the bottom of the floor. look at mosers web site the look at stranges web site ,you will see strange notches the housing to drop the mount down in the housing

I just looked @ the strange site,I dont see that.
slowstang
11-03-2008, 07:56 PM
yeah im an idiot, its team z s web site sorry strange housing is just like mosers
bbc 96 stang
11-09-2008, 11:02 AM
I would go straight to Dave @ TeamZ without hesitation of looking right past anything Alstons or M9.


order it from dave z. these guys are right, i did the research as ill be needing one here real soon. the upper mounts arent in the right spot on a lot of the rear ends... dave is the man.
teddy
11-15-2008, 09:25 PM
I have a Moser and the mounts are way too high!!! I have to have someone fab new brackets for it. It is hitting the shit out of the tires!!
Scott @ DLS
11-15-2008, 09:29 PM
I have a Moser and the mounts are way too high!!! I have to have someone fab new brackets for it. It is hitting the shit out of the tires!!


Have you looked into the DTS housing? They sink the uppers into the housing for better geometry.
lazaris
11-15-2008, 10:44 PM
I have a Moser and the mounts are way too high!!! I have to have someone fab new brackets for it. It is hitting the shit out of the tires!!

I just discovered this as well. I didnt realize that the mounts were higher. I was crushing my tire as well. I saw these. http://www.artmorrison.com/uploads/6403_52D.jpg Im considering using the ears to weld onto the housing to have some adjustability. Then I'll add rod ends onto my control ams.
Outlaw Bill
11-15-2008, 11:36 PM
Have you looked into the DTS housing? They sink the uppers into the housing for better geometry.Its actually a Strange housing!. The Moser and others raise the upper control arm mount and cause major geometry issues. The Strange housing has the upper mounts recessed into the housing for proper geometry. TeamZmotorsports is a great place to purchase the housing from.