notchdan
09-20-2007, 07:55 PM
Car is in Fowlerville MI!!
1989 LX full 8 point chromoly roll cage
through the floor subframe connectors
full 36 inch wheel tubs
completely boxed and reinforced lower torque boxes
Narrowed 8.8 with ford motorsport 4:10 gears, moser spool, 33 spline strange axles with big ford bearings, 5/8 studs
Complete Wolfe racecraft rear suspension, double adj. uppers, single adj. lowers, anti roll bar, etc.
Chassis Engineering coil over rear shocks
Strange adj front struts and coil over kit
Strange drag race front brakes
Aerospace engineering rear brakes
Weld Alumastar wheels
BFG drag radials, BFG front runners
afco alum radiator with elec fan
1995 Cobra 5.0 liter short block
Edelbrock performer RPM alum Heads
crane roller rockers
TFS -Camshaft, Hydraulic Roller Tappet, Advertised Duration 275/279, Lift .499/.510,
explorer intake, do have an old edelbrock performer upper and lower
king cobra clutch
clutch quad w/ adj cable
tremec 3550 trans, pro 5.0 shifter
12 gal fuel cell, mallory elec fuel pump
Fiberglass decklid
Have all parts and pieces for interior, do not have seats, just an old stocker
There is more I am sure, will be adding as this goes on.
This is a project car, does run and drive at this time, fully legal. This car does need paint and some body work. Does have new rockers and new quarter panels that are stretched 1 inch. Will consider selling as roller, at this time I am NOT considering trades, sorry. More pics will be available, please send me a PM and I will try to get back with you as soon as possible. I am an employee of a well known chassis shop so all work was performed by myself.
Thanks
Dan
Asking $9,500.00
$6500 roller Or Best Offer
517-223-4407 home
248-361-9426 cell
1989 LX full 8 point chromoly roll cage
through the floor subframe connectors
full 36 inch wheel tubs
completely boxed and reinforced lower torque boxes
Narrowed 8.8 with ford motorsport 4:10 gears, moser spool, 33 spline strange axles with big ford bearings, 5/8 studs
Complete Wolfe racecraft rear suspension, double adj. uppers, single adj. lowers, anti roll bar, etc.
Chassis Engineering coil over rear shocks
Strange adj front struts and coil over kit
Strange drag race front brakes
Aerospace engineering rear brakes
Weld Alumastar wheels
BFG drag radials, BFG front runners
afco alum radiator with elec fan
1995 Cobra 5.0 liter short block
Edelbrock performer RPM alum Heads
crane roller rockers
TFS -Camshaft, Hydraulic Roller Tappet, Advertised Duration 275/279, Lift .499/.510,
explorer intake, do have an old edelbrock performer upper and lower
king cobra clutch
clutch quad w/ adj cable
tremec 3550 trans, pro 5.0 shifter
12 gal fuel cell, mallory elec fuel pump
Fiberglass decklid
Have all parts and pieces for interior, do not have seats, just an old stocker
There is more I am sure, will be adding as this goes on.
This is a project car, does run and drive at this time, fully legal. This car does need paint and some body work. Does have new rockers and new quarter panels that are stretched 1 inch. Will consider selling as roller, at this time I am NOT considering trades, sorry. More pics will be available, please send me a PM and I will try to get back with you as soon as possible. I am an employee of a well known chassis shop so all work was performed by myself.
Thanks
Dan
Asking $9,500.00
$6500 roller Or Best Offer
517-223-4407 home
248-361-9426 cell