PDA

View Full Version : 82-92 Camaro dropped spindle?

Jake
09-14-2007, 04:42 AM
I cant seem to find any so I assume they dont exist. But I figured it was worth asking just incase. I am looking for a 82-92 Camaro 2" dropped spindle. Either cast or fabricated. Any leads would be appreciated.
Thanks,
-Jake
5678TA
09-14-2007, 06:27 AM
ajeracing.com

$1099 for a pair!!!!!!!!!!!!!!!!!!!!!!:smt119
jackstand
09-14-2007, 06:30 AM
just have dawayne machine you some up
Jake
09-14-2007, 06:54 AM
Thanks! I'll have to call them and see if they offer that in a double adjustible version. I'd prefer to find a dropped spindle by itself since I already have my struts. But I may have to do what I have to do.:D
Jake
09-14-2007, 06:54 AM
just have dawayne machine you some up

Bitch!!:D:D
Racecraft Inc.
09-14-2007, 12:32 PM
Racecraft Inc is making a 2" Drop Spindle for the 3rd gen should have them in about 45 days Check website for progress. http://www.racecraft.com

Mark
Robert1320
09-14-2007, 12:42 PM
Jake,

Make sure you don't have any Rim lower control arm interferance issues.
Depending on the app. I have seen some of the drops cause headaches....
Jake
09-14-2007, 05:59 PM
Racecraft Inc is making a 2" Drop Spindle for the 3rd gen should have them in about 45 days Check website for progress. http://www.racecraft.com

Mark


You guys rock!! Saw your stuff at Joliet. I inquired about them there and now your making them, KICKASS! Thanks!
Jake
09-14-2007, 06:00 PM
Jake,

Make sure you don't have any Rim lower control arm interferance issues.
Depending on the app. I have seen some of the drops cause headaches....


Hopefully that wont be a problem. I have the one piece Alumastars w/ the lesser backspacing. Thanks Robert!
Jason@PaRacing
09-15-2007, 01:11 AM
Pa Racing has them in 2" and standard weight on them is 4.5lbs we also have them for the 1st and 4th gen. Call or e-mail for pics and more info!
Racecraft Inc.
10-10-2007, 06:30 PM
Racecraft Inc. has finished our prototype on the third gen 2" drop spindle and will have a 4th gen tomorrow pics are up on our website in the Camaro section.
No emailing of pics required.

Thanks, Mark

http://www.racecraft.com
Jake
10-10-2007, 10:11 PM
Racecraft Inc. has finished our prototype on the third gen 2" drop spindle and will have a 4th gen tomorrow pics are up on our website in the Camaro section.
No emailing of pics required.

Thanks, Mark

http://www.racecraft.com

That is too awesome!! 1 question for you Mark. Would you guys be able to change the offset of the steering arm(not bent as far)? I understand it would be a one off piece that way and would require an additional charge. My factory spindles have had the steering arms relocated for bumpsteer geometry and I would like to retain that setup if possible.
Thanks!
-Jake
Injected65
10-10-2007, 10:19 PM
Jake,

When you are ready to order them from Racecraft, you can call your reasonably local dealer too ;).


Chris
Jake
10-10-2007, 11:14 PM
Jake,

When you are ready to order them from Racecraft, you can call your reasonably local dealer too ;).


Chris


You can bet your Wheaties I will!:D:D Scott get his flange form you already?
Injected65
10-10-2007, 11:15 PM
I sure hope so. If you talk to him, make sure it showed up.

Chris
Jake
10-10-2007, 11:22 PM
I sure hope so. If you talk to him, make sure it showed up.

Chris


I certainely will. :D